Description:

Finish the cut. Check the fit. Ride with confidence.

After a steerer, seatpost or handlebar tube is cut, the end may still have burrs, high spots or a slightly uneven edge. The ALLTOO Bicycle Tube End Facing Tool helps smooth and level that final surface in short, controlled passes. It is designed for finishing work and small measured corrections, not for cutting a tube to length.

  • Guided contact: The tube clamp and straight guide rod position the spring-loaded facing head over the cut end.
  • Controlled finish: The 100# marked abrasive disc helps tidy burrs and uneven edges while you check progress frequently.
  • Manual or drill-assisted: Turn by hand for close control, or use a suitable drill at low speed with light pressure. A drill is not included.

Best for

  • Finishing a fork steerer after it has been cut to the measured length.
  • Cleaning up a rough seatpost or handlebar tube end before reassembly.
  • Making a small, measured end-face correction when the tube and component maker permit it.

Check fit before ordering

The kit is designed for these nominal outside diameters:

  • Fork steerer: 28.6 mm (1-1/8 in) or 31.8 mm (OD2 / 1-1/4 in)
  • Seatpost: 25.4 mm, 27.2 mm or 31.8 mm
  • Handlebar end: 22.2 mm

Before you order: Measure the tube's actual outside diameter and check that the clamp and insert can hold it securely. The listed sizes are nominal; a matching number alone does not confirm fit.

How to use

  1. Choose the matching plastic insert, place the clamp around the tube and lock it securely.
  2. Align the abrasive disc with the cut end using the guide rod.
  3. Face lightly by hand or with a suitable low-speed drill. Work in short passes and inspect often.
  4. Remove dust and debris, then check the finished edge and component fit.

What's in the box

One facing head and guide assembly, one orange plastic clamp with locking lever, one 100# marked abrasive disc, three orange plastic split inserts and one black U-shaped spacer. The demonstration tube and electric drill are not included.

Frequently asked questions

Will this fix a loose headset?

Only if a confirmed steerer height or end-face issue is the cause. Check headset bearings, spacers, stem position and preload before removing material. Headset play may have other causes.

Do I need a drill?

No. You can use the tool by hand. If using a suitable drill, keep the speed and pressure controlled; do not use impact mode.

Can I use it on a carbon tube?

Follow the tube and component manufacturer's instructions before facing carbon. Remove as little material as necessary, control dust and stop if you are unsure. A qualified bicycle mechanic can assess the setup.

ALLTOO Bicycle Tube End Facing Tool Kit for Steerer, Seatpost & Handlebar

$32.00
$65.00
51% OFF
51% OFF

HURRY! ONLY 100 LEFT

Worldwide free shipping

Storewide Sale

Mix & match any color or size

2 items

5% Off + 🚛 Freeship

3 items

10% Off + 🚛 Freeship

4+ items

Most popular

15% Off + 🚛 Freeship

Our 30-day refund policy allows you to return your purchase for a full refund within 30 days of the original purchase date if you're not satisfied.

Description:

Finish the cut. Check the fit. Ride with confidence.

After a steerer, seatpost or handlebar tube is cut, the end may still have burrs, high spots or a slightly uneven edge. The ALLTOO Bicycle Tube End Facing Tool helps smooth and level that final surface in short, controlled passes. It is designed for finishing work and small measured corrections, not for cutting a tube to length.

  • Guided contact: The tube clamp and straight guide rod position the spring-loaded facing head over the cut end.
  • Controlled finish: The 100# marked abrasive disc helps tidy burrs and uneven edges while you check progress frequently.
  • Manual or drill-assisted: Turn by hand for close control, or use a suitable drill at low speed with light pressure. A drill is not included.

Best for

  • Finishing a fork steerer after it has been cut to the measured length.
  • Cleaning up a rough seatpost or handlebar tube end before reassembly.
  • Making a small, measured end-face correction when the tube and component maker permit it.

Check fit before ordering

The kit is designed for these nominal outside diameters:

  • Fork steerer: 28.6 mm (1-1/8 in) or 31.8 mm (OD2 / 1-1/4 in)
  • Seatpost: 25.4 mm, 27.2 mm or 31.8 mm
  • Handlebar end: 22.2 mm

Before you order: Measure the tube's actual outside diameter and check that the clamp and insert can hold it securely. The listed sizes are nominal; a matching number alone does not confirm fit.

How to use

  1. Choose the matching plastic insert, place the clamp around the tube and lock it securely.
  2. Align the abrasive disc with the cut end using the guide rod.
  3. Face lightly by hand or with a suitable low-speed drill. Work in short passes and inspect often.
  4. Remove dust and debris, then check the finished edge and component fit.

What's in the box

One facing head and guide assembly, one orange plastic clamp with locking lever, one 100# marked abrasive disc, three orange plastic split inserts and one black U-shaped spacer. The demonstration tube and electric drill are not included.

Frequently asked questions

Will this fix a loose headset?

Only if a confirmed steerer height or end-face issue is the cause. Check headset bearings, spacers, stem position and preload before removing material. Headset play may have other causes.

Do I need a drill?

No. You can use the tool by hand. If using a suitable drill, keep the speed and pressure controlled; do not use impact mode.

Can I use it on a carbon tube?

Follow the tube and component manufacturer's instructions before facing carbon. Remove as little material as necessary, control dust and stop if you are unsure. A qualified bicycle mechanic can assess the setup.